1. How to fix and install the glass door lock
Glass door lock installation method
1. Use the U-shaped bracket to install the magnetic lock on the frameless glass door:
The glass door without frame needs accessories to assist in the installation. The installation method is basically the same as the surface installation method of ordinary doors, except that it is different in the third step of installing the iron plate. The U-shaped groove together with the rubber buffer pad and stainless steel The gasket (placed on the side of the lock screw) is set on the glass door, locked on the glass door with a headless hexagon socket screw, and then the relay iron plate is fixed on the U-shaped groove. For different glass door thicknesses and different models Electromagnetic lock.
2. Fixed
Use the AB frame to install. First fix the AB frame on the glass door with glass special glue (or double-sided tape), and then fix the relay iron plate on the bracket.
2. How to install the frameless glass door
Frameless glass door installation points
1. Setting out positioning
2. Install the limit groove on the top of the frameless glass door frame
3. Install the wooden base of the frameless glass door metal finish
4. Install the door frame
5. Glass door leaf installation for frameless glass doors
6. Fixing the glass
7. Inject glass glue seal
8. The butt joint between the glass of the frameless glass door
1. Setting out positioning: At the beginning of the installation of the frameless glass door, the fixed glass partition and the movable glass door leaf must be set out and positioned uniformly. After the position of the door frame is determined, the ground level and the top level of the door frame must be accurately measured.
2. Install the limit groove on the top of the frameless glass door frame: lead out two side lines of the metal decorative plate from the center line of the spring, and then install the limit groove on the top of the door frame according to the side line.
3. Install the wooden base of the frameless glass door metal finish: nail the square wood on the original pre-embedded wooden bricks, or nail the square wood with expansion bolts, fix the square wood on the ground, and then glue the metal veneer to the ground on the wooden side.
4. Install the door frame: Nail the square wood of the door frame according to the center line of the spring, and then use plywood to determine the size and position of the door frame column, and then wrap the metal decorative surface after it is fixed.
5. Glass door leaf installation for frameless glass doors: Use a glass suction cup device (or glass suction cup machine) to suck the thick glass tightly, then hold the suction cup handle and lift the thick glass plate upright and move it to the The installation site is ready.
6. Fixing the glass: Nail two flat square wooden strips inside and outside the bottom bracket to clamp the thick glass in the middle, but leave a gap of about 4mm from the thick glass plate, and then apply glue on the flat square wooden strips. The veneer metal plate is glued to the square wood and two flat square wood strips.
7. حقن غراء الغراء الزجاجي: قم بإدخال غراء الزجاج في الفجوة على جانبي فتحة الجذر العلوي وجانبي الشق الزجاجي للقوس السفلي والمفصل بين الزجاج السميك وعمود إطار الباب.
8. الوصلة التناكبية بين زجاج الباب الزجاجي بدون إطار: اللوح الزجاجي السميك للجزء الثابت يجب أن يتم تجميعه بقطعتين أو أكثر بسبب عرضه الكبير. يجب ترك مسافة 2 ~ 3 مم
المؤلف: بقلم السيدة ريبيكا فو من S4A INDUSTRIAL CO.، LIMITED
Factory Address:Building S4A, South Third Lane, Qiuyuling Street, Zhangkeng Village, Hengli Town, Dongguan City, Guangdong Province Office Address:#601,floor 6 ,building 1,JINFANGHUA industrial zone, Bantian St. Longgang Dist. Shenzhen, PRC.
إذا كنت مهتمًا بمنتجاتنا وترغب في معرفة المزيد من التفاصيل ، فالرجاء ترك رسالة هنا ، وسنرد عليك في أقرب وقت ممكن.